BW Technologies MicroClip XT Specifiche

iERP: XXXXXXDXXXX/X [language/language]© BW Technologies 2008. All rights reserved.1, 2, 3, and 4-Gas DetectorTechnical Reference Guide

ixList of TablesTable Title Page1. Gases Monitored ...

xGasAlertMicroClip XTTechnical Reference Guide

1GasAlertMicroClip XTIntroductiona WarningTo ensure personal safety, read Safety Information - Read First and the Cautions before using the detector.T

GasAlertMicroClip XTTechnical Reference Guide2Contacting BW Technologies by HoneywellTo contact BW Technologies by Honeywell, callUSA: 1-888-749-8878C

3GasAlertMicroClip XTa Cautionsa Cautions• Warning: Substitution of components may impair Intrinsic Safety.• Before using the detector, refer to Senso

4GasAlertMicroClip XTTechnical Reference Guidea Cautions• For use only in potentially explosive atmospheres where oxygen concentrations do not exceed

5GasAlertMicroClip XTa CautionsTable 2. International SymbolsSymbols DescriptionnApproved to both U.S. and Canadian Standards by CSA InternationalgEur

GasAlertMicroClip XTTechnical Reference Guide6Sensor Poisons and ContaminantsSeveral cleaners, solvents, and lubricants can contaminate and cause perm

7GasAlertMicroClip XTGetting StartedGetting StartedThe list below provides the standard items included with the detector. If the detector is damaged o

GasAlertMicroClip XTTechnical Reference Guide8Parts of the GasAlertMicroClip XTFigure 1. Parts of the GasAlertMicroClip XTTable 3. Parts of the GasAle

iTable of ContentsHeading PageIntroduction ...

9GasAlertMicroClip XTDisplay ElementsDisplay ElementsFigure 2. Display ElementsTable 4. Display Elements18765432Item Description1 Alarm condition2 Aut

10GasAlertMicroClip XTTechnical Reference GuidePushbuttonTable 5. PushbuttonPushbutton DescriptionC• To activate the detector press C.• To deactivate

11GasAlertMicroClip XTActivating the DetectorActivating the Detectora CautionOnly activate the detector in a fresh air environment and in a safe area.

GasAlertMicroClip XTTechnical Reference Guide12Startup Message3. If data is entered in the Startup option (25 characters maximum) of Fleet Manager II,

13GasAlertMicroClip XTActivating the DetectorAutomatic Zero and O2 Calibration (optional)6. Auto-Zero on Startup: If enabled, the H2S, CO, and LEL sen

GasAlertMicroClip XTTechnical Reference Guide14Last Calibration Failed (optional)If any sensor failed the last calibration, CAL FAILURE displays on th

15GasAlertMicroClip XTActivating the DetectorLast Bump Test Failed If any sensor failed the last calibration, CAL FAILURE displays on the screen.NoteW

GasAlertMicroClip XTTechnical Reference Guide16Self-Test PassWhen the detector has passed all startup self-tests, it enters normal operation. The LCD

17GasAlertMicroClip XTDeactivating the DetectorDeactivating the DetectorTo deactivate the detector, press and hold C. The detector• performs a sequenc

GasAlertMicroClip XTTechnical Reference Guide18Installing Fleet Manager IIFleet Manager II is required to configure the detector and sensors. And IR L

GasAlertMicroClip XTTechnical Reference GuideTitle PageiiLast Calibration Failed (optional) ...

19GasAlertMicroClip XTInstalling Fleet Manager II9. When the Device Selection dialog box displays, select GasAlertMicroClip / GasAlertMicroClip XT and

GasAlertMicroClip XTTechnical Reference Guide20Figure 3. Connecting the IR Link1. Activate the detector and wait for the startup tests to complete.2.

21GasAlertMicroClip XTDetector IdentificationDetector IdentificationThe Detector Identification section provides information about the detector, curre

GasAlertMicroClip XTTechnical Reference Guide22Sensor ConfigurationSettings for the sensors are configured individually. Enter values or enable/disabl

23GasAlertMicroClip XTSensor Configuration3. Click the Save to Device button located at the bottom of the window.4. The detector LCD automatically upd

GasAlertMicroClip XTTechnical Reference Guide24Bump IntervalDefine how often a bump check should be performed for each sensor in the Bump Interval fie

25GasAlertMicroClip XTSensor Configuration2. Enter the setpoint in the TWA Alarm field. STEL AlarmThe short-term exposure limit (STEL) is the maximum

GasAlertMicroClip XTTechnical Reference Guide26O2 Auto-Calibration on Startup (Automatic O2 Calibra-tion)When enabled, the O2 sensor is automatically

27GasAlertMicroClip XTUser OptionsCal Lock (Calibration IR Lock)When enabled, the sensors can only be calibrated using an infrared (IR) device to ensu

GasAlertMicroClip XTTechnical Reference Guide28with the IR Link. This option is available only if configuring the GasAlertMicroClip with the base stat

iiiGasAlertMicroClip XTTechnical Reference GuideTitle PageAuto Zero on Startup...

29GasAlertMicroClip XTUser OptionsIntelliFlashWhen enabled, the green LED flashes to provide continuous visual con-firmation that the detector is oper

GasAlertMicroClip XTTechnical Reference Guide30Stealth ModeWhen enabled, the backlight, visual alarms, and audible alarms are dis-abled. displays co

31GasAlertMicroClip XTAlarmsAlarmsTable 7. describes the detector alarms and corresponding screens. During an alarm condition, the detector activates

32GasAlertMicroClip XTTechnical Reference GuideAlarm Screen Alarm ScreenMulti-Gas Alarm• Sequence alternating low and high alarm siren and flash• L an

33GasAlertMicroClip XTAlarmsComputed Gas Exposuresa WarningTo avoid possible personal injury, do not deactivate the detector during a work shift. TWA,

GasAlertMicroClip XTTechnical Reference Guide34Clearing Gas Exposuresa CautionFollow all safety procedures as defined by your employer.Confirm with yo

35GasAlertMicroClip XTAlarmsFactory Gas Alarm SetpointsNoteStandard factory alarm setpoints may vary by region.Table 10. lists the factory alarm setpo

GasAlertMicroClip XTTechnical Reference Guide36Sensor AlarmThe detector tests for missing or defective sensors during the startup self-test and contin

37GasAlertMicroClip XTBump TestBump Test

GasAlertMicroClip XTTechnical Reference Guide38CalibrationGuidelinesWhen calibrating the detector, adhere to the following guidelines:• Recommended ga

GasAlertMicroClip XTTechnical Reference GuideTitle PageivAutomatic Deactivation Alarm ...

39GasAlertMicroClip XTCalibrationConnecting the Gas Cylinder to the DetectorRefer to the following Figure 8., Table 11., and procedures to connect the

GasAlertMicroClip XTTechnical Reference Guide40Calibration SetupThe following calibration procedures are written as calibration perfor-mance is intend

41GasAlertMicroClip XTCalibration8. Ensure the sensors to be calibrated are enabled in Fleet Manager II.9. Using , select the concentration value(s)

GasAlertMicroClip XTTechnical Reference Guide42Auto Zero and Oxygen Sensor CalibrationNoteDo not apply calibration gas until APPLY GAS displays, other

43GasAlertMicroClip XTCalibrationWhen a sufficient amount of gas has been detected (approxi-mately 30 seconds after the gas has been applied), the det

GasAlertMicroClip XTTechnical Reference Guide446. After calibration is complete, CAL DUE displays and all successfully calibrated sensors automaticall

45GasAlertMicroClip XTCalibrationVerification1. After calibration is complete and the detector returns to normal operation, verify the calibration usi

GasAlertMicroClip XTTechnical Reference Guide46DatalogsThe detector records various information that can be compiled to create a report. The detector

47GasAlertMicroClip XTMaintenanceBattery Cautionsa WarningTo avoid personal injury and/or property damage, adhere to the following:• The detector must

GasAlertMicroClip XTTechnical Reference Guide48Table 12. Connecting the Charging Adaptera WarningThe detector must be charged in a safe area that is f

vGasAlertMicroClip XTTechnical Reference GuideTitle PageStartup Troubleshooting ...

49GasAlertMicroClip XTMaintenanceReplacing a Sensor or Sensor Filtera WarningTo avoid personal injury, only use sensors that are specifically designed

GasAlertMicroClip XTTechnical Reference Guide50Table 13. Replacing a Sensor or Sensor Filter1. Deactivate the detector. On a clean surface, place the

51GasAlertMicroClip XTMaintenanceNoteDetectors that are configured for 1, 2, or 3 gases may contain a dummy sensor in one of the four sensor locations

GasAlertMicroClip XTTechnical Reference Guide525. Carefully replace the circular rigidified flex PCB atop the metal sensor posts. Ensure the purple pl

53GasAlertMicroClip XTTroubleshootingTroubleshootingIf a problem occurs, refer to the solutions in the Troubleshooting section. If the problem persist

54GasAlertMicroClip XTTechnical Reference GuideTable 14. TroubleshootingProblem Possible Cause SolutionDetector OperationDetector does not display exp

55GasAlertMicroClip XTTroubleshootingTable 14. TroubleshootingProblem Possible Cause SolutionDetector intermittently enters alarm without reason.Ambie

56GasAlertMicroClip XTTechnical Reference GuideStartup TroubleshootingError Screen Problem Solution Error Screen Problem SolutionSensor ErrorThe senso

57GasAlertMicroClip XTCalibration TroubleshootingCalibration TroubleshootingError Screen Problem Solution Error Screen Problem SolutionAuto-zero Unsuc

GasAlertMicroClip XTTechnical Reference Guide58Replacement Parts and Accessoriesa WarningTo avoid personal injury and/or damage to the detector, use o

GasAlertMicroClip XTTechnical Reference GuideTitle Pagevi

59GasAlertMicroClip XTReplacement Parts and Accessories*Add one of the following applicable suffixes to the end of the order number to ensure power ad

GasAlertMicroClip XTTechnical Reference Guide60SpecificationsInstrument dimensions: 11.25 x 6.00 x 2.89 cm (4.4 x 2.4 x 1.1 in.)Weight: 170 g (6.0 oz.

61GasAlertMicroClip XTSpecificationsApprovals:Approved by CSA to both U.S. and Canadian StandardsCAN/CSA C22.2 No. 157 and C22.2 152ANS/UL – 913 and A

GasAlertMicroClip XTTechnical Reference Guide62

iERP: 131475-L3D6568/0 [English]© BW Technologies 2010. All rights reserved.1, 2, 3, and 4-Gas DetectorTechnical Reference Guide

viiList of FiguresFigure Title Page1. Parts of the GasAlertMicroClip XT......

viiiGasAlertMicroClip XTTechnical Reference Guide